Aircraft in Plastic Decals
[ Page 2 ]
[ Page 2 ]
Custom decals designed by Meindert de Vreeze
.... continued from decal page 1....
Interested in a sheet for personal use? Or if you need another scale, let me know as noted at decal page 1...
DECAL
PAGE 1
PAGE 2
PAGE 3
PAGE 4
PAGE 5
PAGE 6
PAGE 7
PAGE 8
PAGE 9
DECAL SYSTEM
Each decal sheet is LASER full colour printed on one continuous print film, so each decal needs to be cut out with fine scissors.
No other prior decal preparation is needed.
Each cut out decal can be applied as usual after soaking it a short while in water. Decals are VERY THIN, so slide off from the wet backing sheet on a horizontally held GLOSSY model surface.
Note 1: a decal that contains a large white section is often split in two parts. To apply the full decal marking, first set the white decal section at correct position and than on top of that the coloured section. On the decals sheet you will often see an “arrow” to indicate this way of application (on white model surfaces, the white section may not be needed).
Note 2: sometimes a white edge is unavoidable on a specific decal; remove the tiny white edge with fine scissors or overpaint the edge later on the model.
Note 3: please be aware these are hobby custom decals of subjects often not available, not commercial decals.
After all decals have been applied, finish the model with your preferred final gloss, matt or semi-matt varnish coats. This will also protect all the decals.
IMPORTANT: Please do not expect excellent "Cartograph" like quality! These decals are home made laser printed and of rare subjects for which no large series printed commercial decalsare available!
These decals are for a 1/72 Tornado IDS GR4 with a special scheme as it had flown 1,000,000 hours in service. This RAF GR 4 had code ZA547 [c/n 060/BS016/3031]. It has the standard colours but black spine and vertical tail.
A double sheet is provided to ensure good coverage over the black areas.
(1/72 sheet size approx 15x3 cm / 6x1 inch)
DOWNLOAD description sheet AIPD 17Look at PHOTO's and INFORMATION links:
Flickr.com photo-1
Airplane-pictures-net Photo 2
Shenyang J-6 / F-6 (“MiG-19S Farmer C”) as on display at the China Military museum, Beijing. Is in full bare metal with red markings.
Some markings are "double" provided as are some stencils.
(1/32 sheet size approx 16x12 cm/ 6x5 inch)
Other scales on request
DOWNLOAD description sheet AIPD 20Recommended kit: 1/32 Trumpeter MiG-19S "Farmer C" #2207
Look also at PHOTO's and INFORMATION links:
Airliners-net photo 1
Airliners-net photo 2
Shenyang F-6C (“MiG-19S”) of the Pakistan Air Force.
Choices of 2 schemes: No 26 Black Spiders squadron “427” in metal scheme or No 19 squadron camouflaged “10602”.
By combining, other schemes may be possible. One of the schemes has 2 grey colours, the exact numbers are unknown but may be similar to the 2 grey PAF F-16 seen here....
(1/32 sheet size approx 17x23 cm / 7x9 inch) Large!
Other scales on request.
DOWNLOAD description sheet AIPD 21Recommended kit: 1/32 Trumpeter MiG-19S #02207
Look at PHOTO's and INFORMATION links:
Flickr.com photo 1
Airhistory.net photo 2
Wikipedia link
In 1996 Thailand acquired from Spain 7 AV-8A(S) with codes 3103-3109 and 2 TAV-8A(S) two seaters coded 3101 and 3102. These would be flown by the Thai Navy to operate from the also purchased ex-Spanish carrier, now called in Thailand "HTMS Chakri Naruebet". However, the Thai AV-8 jets operated mainly from shore and for just a few years.
(1/32 sheet size approx 15x10 cm / 6x4 inch)
Recommended kit: old 1/32 Revell Harrier
No decal instructions have been prepared but all details including Fed.Std colours and much more...
Look at my Thai AV-8A modelling report here...
The Royal Thai Air Force acquired a large number of Diamond DA.42 Twin Stars that were delivered from mid 2009. Several versions are used.
The base colour is white with blue and red/orange panels and stripes on fuselage sides and tail. Decals for a few DA.42 NG. Any very thin white stripes on the winglets and tail are to be painted or obtained from stripe decals.
NOTE: updated.
(1/72 sheet size approx 9x8 cm / 4x3 inch)
DOWNLOAD description sheet AIPD 23Recommended kit: 1/72 A-Model Diamond DA.42 Twin Star #72380 or #72374
No model has yet been made by me.
Look also at PHOTO's and INFORMATION links:
Airhistory.net photo 1
JetPhotos photo 2
Several R-22 helicopters were delivered to the Phillippines Navy. Such as R-22B Beta II delivered ~2020.
Overall colour seems overall gloss white.
(1/72 sheet tiny size approx 6x3 cm / 2x1 inch)
Recommended kit: 1/72 Pavla R-22 #72017
No model has yet been made, is planned.
No decal instructions have been prepared as application is quite obvious. Look at PHOTO's and INFORMATION links:
Maxdefense B. Anido photo 1/ photo
Dozens of Eurocopter EC-145 (BK117C-2) helicopters have been delivered to the Kazachstan Air Force from 2011.
yellow 07 c/n 9550
(1/72 sheet tiny size approx 7x2 cm / 2 1/2 x 1 inch)
The overall colour is unknown but looks blue-grey.
Recommended kit: 1/72 Revell EC-145
No model has yet been made, is planned.
As decal application is quite obvious, no decal instructions have been prepared. Look at PHOTO's and INFORMATION links:
Flickr.com photo 1
Flickr.com photo 2
During January 1959, Indonesia ordered 18 Gannet AS.4 and T.5s for the Indonesian Navy. These were purchased from Fairey via the Ministry of Supply and were re-modelled from existing Gannet AS.1s and T.2s prior to delivery.
(photo courtesy: Henk Hirs at IPMS.NL)
(1/72 sheet size approx 15x3 cm / 6x1 inch)
Recommended kit: 1/72 Revell Gannet / Trumpeter Gannet
No decal instructions have been prepared as application is quite obvious. The paint scheme looks similar to the FAA scheme.
Look at PHOTO's and INFORMATION links:
Recommended reference: IPMS U.K SIG Asian Air Arms newletter #37, June 2023
IPMS Nederland Fairey walk around
Ten surplus Dutch Navy helicopters refurbished by Westland for the Indonesian Navy TNI-AL were flown by 400 Squadron (RON 400) from NAS Juanda. When at sea, they were embarked upon the Indonesian Navy's ex-Royal Navy Tribal-class and ex-Dutch Navy Van Speijk-class frigates.
Probably overall gloss gull grey scheme. Codes 432 or 434 on the sheet.
(1/72 sheet size approx 7x3 cm / 3x1 inch)
Recommended kit: UPDATE... LF Models released a Wasp in 1/72 scale.
No model has yet been made in the Indonesia Navy scheme by me. An old Dutch MLD Wasp model is seen here....
No decal instructions have been prepared as decal application is quite obvious. Look at PHOTO's and INFORMATION links:
Indomiliter article
After the collapse of the Soviet Union (USSR), several jets were transferred to the independent Republics. MiG-25 "Foxbats" were used by Turkmenistan from the 1990s.
Colour scheme similar to USSR MiG-25 with overall grey.
(1/72 sheet size approx 11x6 cm / 4x2 inch)
Recommended kit: 1/72 ICM MiG-25
No model has yet been made in this scheme. Another MiG-25 model can be seen here...
No decal instructions have been prepared as application is quite obvious.
PHOTO's and INFORMATION links:
rare.... almost non existant
The A-6F Intruder II was a development program of Grumman to improve the US Navy A-6E. It would also get 2 new F-404-GE-404 jet engines with 15% more power and lower fuel burn. Armament could now also include air-to-air missiles and HARM missiles on outboard wing pylons as well as new systems. The new GE- engines required deeper and bulkier engine nacelles. No A-6F were ordered for the US Navy.
A 1/72 A-6E can with some conversion be made as A-6F. (C-Scale had a soft casted metal conversion set but this is rare). The decal sheet description describes how the conversion can be done from scrap and the decals offer a choice of 2 A-6F schemes.
(1/72 sheet size approx 17x10 cm / 6x4 inch)
DOWNLOAD description sheet AIPD 29Recommended kit: 1/72 Fujimi A-6E TRAM #27013 / H-13 series
No model has (yet) been made.
PHOTO's and INFORMATION links:
AviationGeek
AerospaceWebOrg
Birma (1/72)
Between 1957 and 1958, Burma received 21 Sea Furies, the majority of them being British ex-FAA aircraft. The Sea Fury was frequently employed as a counter-insurgency platform in Burmese service in the early sixties.
(photo courtesy: BAe systems )
Note view “periscope” for the instructor. Overall colour probably silver dope paint. Paint the circular yellow band at rear fuselage.
(1/72 sheet size approx 9x6 cm / 4x2 inch)
Recommended 1/72 kit: Matchbox T.20 Sea Fury trainer or Pioneer (rare!)
As scheme and decal application is quite obvious, no decal instructions have been prepared. Look at PHOTO's and INFORMATION links:
BAe photo 1
A few DHC L-20 Beavers were delivered in 1955/ 1957 as the Beaver short takeoff and landing capabilities were well suited it for the primitive conditions of Laotian airstrips. One or more of these L-20s arrived with a .50 caliber machine gun still mounted; the natural use for such an armed craft was as a gunship for strafing ground targets.
Colour probably overall gloss light grey. It is unclear how many roundels were carried at the wing. (but 6 are provided).
(1/72 sheet size approx 7x5 cm / 3x2 inch)
Recommended 1/72 kit: Airfix Beaver (vintage re-released 2023) or old rare kit Hobbycraft
No decal instructions have been prepared as application is quite obvious. Look at PHOTO's and INFORMATION links:
wings-aviation.ch photo 1
The Royal Thai Navy had a few F-27 in service in the 2000’s.
Colours are white and probably “gull grey” upper surfaces. (large Fokker logo is for a display).
(1/72 sheet size approx 15x7 cm / 6x3 inch)
Recommended 1/72 kit: old Airfix F-27 (that to be honest needs quite some improvements), look at my Airfix F-27 model page here...
No decal instructions have been prepared as application is quite obvious.
Look at PHOTO's and INFORMATION links:
Airliners.net photo 1
Jetphotos.com photo 2
A rather unknown alternative painted F-117 Stealth fighter with nick name “toxic death”. Some areas seen to be “metal” and shows primer without the secret black stealth paint coats. “Ray Who”, probably Ray being the pilot first name with some red V symbols are situated at the right cockpit area. The white unit badge is unclear as well as the serial but the ED code seems to be used on the tail.
(source: The Drive )
(1/72 sheet size approx 7x2 cm / 3x1 inch)
Recommended 1/72 kit: Italeri F-117
No model has yet been made, is planned. But a standard scheme 1/72 F-117 model is seen here..
No decal instructions have been prepared as application is quite obvious. Look at PHOTO's and INFORMATION links:
The Drive photo 1
Photos on internet are rare. Search "F-117 Toxic death"
The Pakistan Air Force also used the H-43 Huskie helicopter. This is a camouflaged scheme.
The exact camouflage colours are unknown but are medium gloss grey and green. Code 4556 "white".
(1/32 sheet size 12x10 cm / 5x4 inch)
(1/72 sheet size 4x4 cm / 2x1 1/2 inch)
Recommended 1/32 kit: Testors
Recommended 1/72 kit: Croco resin
No decal instructions have been prepared as application is quite obvious. Look PHOTO's and INFORMATION links:
Airliners.net photo 1
Pafsqk info
Pakistanfalcons info
The Chengdu F-7 is a significantly modified Chinese version of the old Soviet MiG-21 F13. It got a cranked double delta wing and upgraded systems. In Bangladesh and Namibia these jets are flown as main fighter. Note the cranked wing of this version.
Namibia:
(1/32 sheet size approx 17x16 cm / 8x6 inch)
Other scales on request
DOWNLOAD description sheet AIPD 38Recommended 1/32 kit: Trumpeter "Chinese F-7 MG" #02220.
Making this model needs research and the decal sheet offer many choices. Also check out the PHOTO's and INFORMATION links:
Airliners.net photo
Planespotters.net photo
defensetiger info
A decal sheet for AMX Ghibli aircraft of the Italian Air Force (AM) "Aeronautica Militare" with colourful tails as seen at the 30th anniversary in 2019. The Italian roundels stencilling, maintenance markings and items like the low-visibility strips are to be used from the kit. Scheme [3] is for a AMX-T.
(1/72 sheet size approx 17x8 cm / 6x3 inch)
Recommended 1/72 kit: Italeri AMX #1460 or AMX-T #1471 trainer
DOWNLOAD instructions sheet AIPD 40A few models were made, look at the AMX modelling report here...
A decal sheet for AMX/ EMBRAER A-1 jets of the Brasil Air Force (FAB) “Força Aérea Brasileira”. With markings for grey and camouflaged AMX with several codes and badges and the different Brazil national marking "stars". Also markings for the modernized A-1M. The stencilling, maintenance markings and items like the low-visibility strips are to be used from the kit.
(1/72 sheet size approx 10x10 cm / 4x4 inch)
Recommended 1/72 kit: Italeri AMX #1460 or AMX-T #1471 trainer
NOTE: this kit needs some modifications for the Brasil AMX A-1: change the shape of both canon fairings for the 30 mm DEFA canons. The nose shape looks (almost) unchanged. The A-1M modernized jets obtained additional bulged ECM fairings on the rear fuselage and forward fuselage and smaller changes.
DOWNLOAD description sheet AIPD 41A few 1/72 models were made of the A-1, check out here....
For obtaining a decal sheet (different scales may be possible), see these notes...
On to next [ Decals page 3.... ]
(c) Copyright Meindert "designer"/ All rights reserved.
Your comments are welcomed by webmaster
Created this page:
November, 2023